Xbox/Playstation GH5 – Solderless Kit
Xbox/Playstation GH5 RGB Solderless Kit
Note on text/pictures: This guide uses color coded steps and images. For example, instructions that have a green dot next to them will relate to green shapes in the accompanying images (usually an arrow). Same for all other colors.
Note on Component Bag: You will have leftover components after completing the mod; this is normal.
Tools Needed/Parts Included
Tools needed (not included):
- Wire Strippers (24 AWG recommended)
- Flush Cutters
- Screwdriver and Bits (T6, T10, PH1, PH2, 1/16th inch flathead)
Purchase Links: Wire Strippers Screwdriver + Bits Flush Cutters
Parts Included with the kit:
- Component Bag
- USB-C Cable
- 3x JST Cables (twisted)
- 5x 3D Printed Frets (translucent)
- Zeroboard SL
- Fretboard SL
- 2x 3-Pin Jumper Cable
- 2x 3-Pin Splicer
Opening the Controller
- Move the faceplate latch to the unlocked position on the back of the body, then remove the faceplate by pulling upwards from the neck slot.
- Front body shell - 12x T10 screws
- Front body shell (neck) - 4x PH0 screws
- Rear neck shell - 11x T10 screws
- Ensure that all of the screws are removed, and open the shell. I recommend starting to pry gently from the opening near the neck connector.
Once the shell begins to open, slowly move down the rest of the shell until it pops open completely.
- Repeat this process for the neck, using the opening at the neck connector and working towards the headstock.
If the shell seems to gets stuck, DO NOT FORCE IT. Check to make sure you have removed all of the screws before continuing to pry the shell.
Cutting the stock wires
We will be making cuts on some of the stock wires in the shell to prepare them for the new boards. Use your flush cutters for this and follow the instructions carefully!
- Cut the wires connecting the start/select board, whammy, and dpad to the mainboard connector. Cut as close as possible to the mainboard to leave plenty of wire to run to the new strumboard. Cut the battery connector wires as well.
- Xbox models only: Cut the two wires going to the Xbox headset port.
Removing stock boards
Now its time to remove the stock boards that will be replaced with the new boards included in the kit. For most models these boards will use PH1 screws, but some use T6.
- Remove the screws on the stock strumboard, mainboard, and RJ11 port. There are a total of 6 PH1 screws that need to be removed.
- Remove the single PH1 screw holding down the fretboard in the neck. When you remove the fretboard, all of the connected boards need to come out as well.
Keep the start/select board, whammy, and dpad in the body.
Making some shell modifications (optional, but recommended)
We can now make some small modifications to the neck shell to make routing the new wires much easier when we get to that step. This is not required, but I highly recommend taking the few minutes needed to do this!
- Start by removing the bottom-most screw post on the rear neck shell. This should be removed to prevent the new wires from being crushed by the shell.
- Cut out square slots on the flat supports connected to the screw posts on the front neck shell. This will ensure that the wires have a clear path out of the neck shell. This will also ensure they are not damaged when the shell is put back together.
The remaining plastic does not need to be perfectly flush for a proper fit, but you should clear away any jagged edges left behind from the cuts.
Preparing wires for the Zeroboard SL
We will now need to prepare the wires for the new strumboard. We’re going to use the 22 AWG slot of our wire strippers to do so.
- Separate the 3 or 4 wires of the ribbon cable coming from the start/select board. Strip away about 1/3 of an inch (1 cm) of sheathing from the wire.
- Separate the 3 wires of the ribbon cable coming from the whammy bar. Strip away about 1/3 of an inch (1 cm) of sheathing from the wire.
-
Insert all 3 of the JST cables (twisted) into the 3 JST connectors on the Zeroboard labelled:
RGB LED
GND/ORANGE/BLUE
YELLOW/RED/GREEN
How to use the splicers and screw terminals
Here’s how to use the grey and orange splicers just in case the stock wires do not reach the new Zeroboard. It is recommended to twist the exposed wires with your finger to make them easier to insert.
- Lift the orange lever to open the slot on the splicer.
- Insert the wire into the slot, making sure that the exposed metal of the wire is touching the metal in the slot, and not the sheathe the wire. Snap the orange lever down to engage the clamp on the wire.
Here’s how to use the green screw terminals on the Zeroboard to connect the stock boards and whammy.
- Using your 1/16th inch flathead bit, turn the screw counter-clockwise to open the terminal slot.
- Insert the expose metal of the wire into the slot, then rotate the screw clockwise to clamp it down onto the wire.
Make sure that none of the exposed metal of the wires are touching each other; this may cause bridging issues.
Installing the Zeroboard SL
Now we will connect the remaining stock boards to the new strumboard.
- Using 4 screws from the component bag and a PH1 bit, install the Zeroboard SL onto the standoffs that the old strumboard sat on. Make sure the twisted JST wires are not caught under the Zeroboard. You can also use the stock screws if you want!
Connect the 3 wires coming from the start/select board into the section of the Zeroboard SL labelled SEL/START/GND. The wires will not reach by themselves, so refer to the previous section on how to use the wire splicers and jumper wires!
-
Playstation Models:
ST on stock board to START on Zeroboard
GND on stock board to GND on Zeroboard
SEL on stock board to SEL on Zeroboard
-
Xbox Models:
ST on stock board to START on Zeroboard
Twist COL1 and COL2 together on stock board to GND on Zeroboard
SEL on stock board to SEL on Zeroboard
-
Whammy bar (both models):
Center wire on whammy to ADC on Zeroboard
The remaining 2 wires can go to either two remaining open terminals, order does not matter.
Installing the Fretboard SL
Next, we will install the new mechanical fretboard and translucent frets.
- Connect the other ends of the twisted JST wires from the Zeroboard to the corresponding connectors on the new Fretboard. Make sure these connections are fully inserted into the connectors. (Refer to the example image)
- Remove the stock frets and replace them with the translucent 3D printed frets provided in the kit. These frets must be used even if you do not want to use LEDs; the stock frets will not fit with the new Fretboard.
- Using 1 screw from the component bag and a PH1 bit, install the new Fretboard onto the standoffs that the old fretboard sat on. Make sure the twisted JST wires are not caught under the board or screws. The other end of the fretboard is held down by the rear neck shell, so do not worry if the board feels "loose".
Coil up the excess wire and use a piece of tape to hold it down to the neck shell. Make sure the cable is clear of any plastic standoffs, as this can pinch and even break the cable if they are in the way when you reassemble the shell.
Installing the tilt sensors and USB cable
Now its time to install the tilt sensors and USB-C cable, as well as test all of our connections!
- Insert the tilt sensors into the slot as pictured. Bend the sensors to the left side and down towards the bottom of the board until they sit at about a 45 degree angle. We will fine tune the tilt angle shortly.
- Connect the USB-C cable into the USB-C port on the Zeroboard. I recommend looping the cable once near the USB-C end and seating it under the edge of the start/select board. This way, if the cable was yanked on, it wouldn't easily disconnect from the Zeroboard!
Programming the guitar and calibrating whammy
If you haven’t already, download the programming tool from this link:
RCM Programming Tool
- Check your Zeroboard SL to determine if it is the original version or version 1.1. The 1.1 version will have "v1.1" on the board, while the original will not have any version number. This will determine which preset gets applied in the next step.
- Connect the guitar to a USB port directly connected to your PC (not a USB hub). Open the tool and select Zeroboard SL (Solderless Kit) for Device Type, and Zeroboard SL - Default if the board is original, or Zeroboard SL - Default v1.1 for the v1.1 board version under Device Variant. Then, click Erase and Configure.
- Once the status bar is at 100%, click Configure. Click the arrow on the Whammy section to expand it. Click Calibrate, then with the whammy bar untouched, click Next. While holding the whammy all the way down, click Next again. Let the whammy go, and then push down on it very slightly and click Next again. Your whammy bar should now be calibrated!
If you’d like to use the default RGB LED fret colors, click Save Settings and you’re done! If not, you can expand all of the different frets and set their pressed and released color to whatever you’d like!
Tuning the tilt angle
- Open your Start Menu, type in "joy.cpl", and hit Enter.
- Select the guitar controller and click Properties.
- Click the Test tab.
- Slowly tilt the guitar neck upwards until the Z Rotation axis goes to 100%. If it hits 100% at too low of an angle for your tastes, physically angle the sensors down towards the bottom of the Zeroboard, creating a more aggressive tilt angle. If it activates too high, then bring the sensors back up closer to horizontal.
Test all the other buttons and make sure that each one corresponds to a button lighting up on the Test tab!
Finishing Up
You’re almost done! Once you have ensured that each input works and that the tilt angle is where you want it to be, we can close up the guitar!
Make sure none of the wires are in the way of any plastic standoffs, as this will damage them when closing the shell. I would recommend taping down the wires to ensure they are out of the way.
With the front body and neck shell facing down, put the rear neck shell onto the front neck shell. You will need to apply pressure to close the shell. If you feel like part of the shell will not snap into place, open it up and double check that there is nothing blocking the standoffs. Repeat for the body shell.
After both sides are clamped down, install all of the screws you removed earlier:
- 10 T10 screws for the neck. Do NOT insert the screw closest to the neck connector if you made the neck shell modifications listed earlier!!! If you do this you WILL damage the new twisted wires.
Insert the neck shell into the body before screwing the body shell back together!
- 12 T10 screws for the body.
- 4 PH0 screws for the body.
After everything is closed up, do not attempt to remove the neck from the body. If you think you may accidently do this in the future, I’d recommend putting some tape over the release lever on the back of the body to block it. Start playing!
Experiencing any issues? Reach out to me: support@RetroCultMods.com
